Search Results

Underhood simulations are proving to be crucially important in a vehicle development program, reducing test work and time-to-market. While Computational Fluid Dynamics (CFD) simulations for steady forced flows have demonstrated reliable, studies of transient natural convective flows in engine compartments under heat-soak (key-off condition with engine and turbocharger emitting high heat flux) are not yet carried out due high computing demands and lack of validated work. The present work aims to computationally characterize the thermally-driven flow in a simplified half-scaled underhood compartment and to experimentally determine the validity of the CFD approach. The commercial software VECTIS was employed for the numerical simulations. Surface temperatures of components as well as the spatial distribution of the air temperature were measured under both steady state and transient (cooling) condition.

Mechanisms exist to vary valve lift, duration and phasing either simultaneously or individually but it remains a challenge to find the optimum settings. An experimental investigation involving a statistical approach has been applied to a 4-litre, 90° vee-8, 4-valve engine in which intake valve lift, duration and phasing were chosen as variables along with exhaust valve phasing. The intake valves were operated symmetrically for the first phase of testing, but subsequently asymmetric operation was also investigated. The results indicated possible strategies that could be applied to reduce emissions.

Two-dimensional Mie-scattering and laser-induced fluorescence techniques were applied to investigate the effects of fuel composition on mixture formation within a firing direct-injection spark-ignition (DISI) engine. A comparison was made between the spray characteristics and in-cylinder fuel distributions resulting from the use of a typical multi-component gasoline (European specification premium-grade unleaded), a single-component research fuel (iso-octane), and a three-component research fuel (iso-pentane, iso-octane and n-nonane). Studies were performed at three different injection timings under cold and part-warm conditions. The results indicate that fuel composition affects both the initial spray formation and the subsequent mixture formation process. Furthermore, the sensitivity of the mixing process to the effects of fuel volatility was shown to depend on injection timing.

This paper describes the application of a new technique, Phosphorescent Particle Tracking (PPT), to the visualisation of gas flow streams in the cylinder of an engine flow rig. This technique uses small phosphorescent tracer particles suspended in the air-stream to provide evidence of the gas flow profile as they are carried away from the plane of excitation. A two colour version of the technique is also presented. This latter technique is shown to have the potential to reveal the interaction or degree of stratification of two flow streams within the cylinder.

This paper describes a method for interactive manipulation of digital human models using the Lagrange multiplier method to simulate their motion under the approximation of first order dynamics, where F = mν. This method provides a natural framework for mixing rigid constraints with flexible goals in both Cartesian and joint space. Features like gravity and contact can thus be incorporated according to strict mathematical principles. We have implemented such a system for the specific task of positioning vehicle occupant models. Although the Lagrange multiplier method for solving constrained dynamics is well documented, its utility in this context has not been widely recognised.

Flash-boiling of sprays may occur when a superheated liquid is discharged into an ambient environment with lower pressure than its saturation pressure. Such conditions normally exist in direct-injection spark-ignition engines operating at low in-cylinder pressures and/or high fuel temperatures. The addition of novel high volatile additives/fuels may also promote flash-boiling. Fuel flashing plays a significant role in mixture formation by promoting faster breakup and higher fuel evaporation rates compared to non-flashing conditions. Therefore, fundamental understanding of the characteristics of flashing sprays is necessary for the development of more efficient mixture formation. The present computational work focuses on modelling flash-boiling of n-Pentane and iso-Octane sprays using a Lagrangian particle tracking technique.

Improvements in the efficiency of internal combustion engines and the development of renewable liquid fuels have both been deployed to reduce exhaust emissions of CO2. An additional approach is to scrub CO2 from the combustion gases, and one potential means by which this might be achieved is the reaction of combustions gases with sodium borohydride to form sodium carbonate. This paper presents experimental studies carried out on a modern direct injection diesel engine supplied with a solution of dissolved sodium borohydride so as to investigate the effects of sodium borohydride on combustion and emissions. Sodium borohydride was dissolved in the ether diglyme at concentrations of 0.1 and 2 % (wt/wt), and tested alongside pure diglyme and a reference fossil diesel. The sodium borohydride solutions and pure diglyme were supplied to the fuel injector under an inert atmosphere and tested at a constant injection timing and constant engine indicated mean effective pressure (IMEP).

This paper presents a study of the combustion mechanism of hydrous and anhydrous ethanol in comparison to iso-octane and gasoline fuels in a single-cylinder spark-ignition research engine operated at 1000 rpm with 0.5 bar intake plenum pressure. The engine was equipped with optical access and tests were conducted with both Port Fuel Injection (PFI) and Direct Injection (DI) mixture preparation methods; all tests were conducted at stoichiometric conditions. The results showed that all alcohol fuels, both hydrous and anhydrous, burned faster than iso-octane and gasoline for both PFI and DI operation. The rate of combustion and peak cylinder pressure decreased with water content in ethanol for both modes of mixture preparation. Flame growth data were obtained by high-speed chemiluminescence imaging. These showed similar trends to the mass fraction burned curves obtained by in-cylinder heat release analysis for PFI operation; however, the trend with DI was not as consistent as with PFI.

International obligations to reduce carbon dioxide emissions and requirements to strengthen security of fuel supply, indicate a need to diversify towards the use of cleaner and more sustainable fuels. Hydrogen has been recommended as an encouraging gaseous fuel for future road transportation since with reasonable modifications it can be burned in conventional internal combustion engines without producing carbon-based tailpipe emissions. Direct injection of hydrogen into the combustion chamber can be more preferable than port fuel injection since it offers advantages of higher volumetric efficiency and can eliminate abnormal combustion phenomena such as backfiring. The current work applied a fully implicit computational methodology along with the Reynolds-Averaged Navier-Stokes (RANS) approach to study the mixture formation and combustion in a direct-injection spark-ignition engine with hydrogen fuelling.

Logistic regression analysis for accident cases of NASS-PCDS (National Automotive Sampling System-Pedestrian Crash Data Study) clearly shows that the extent and the degree of pedestrian's lower extremity injury depend on various factors such as the impact speed, the ratio of the pedestrian height to that of the bonnet leading edge (BLE) of the striking vehicle, bumper to knee ratio, bumper lead angle, age of the pedestrian, and posture of the pedestrian at the time of impact. The pedestrian population is divided in 3 groups, equivalent to small-shorter, medium-height and large-taller pedestrian with respect to the “pedestrian to BLE height-ratio” in order to quantify the degree of influence of lower leg injuries in each group. Large adult male finite element model (95th percentile male: 190 cm and 103 kg) was developed by morphing the Japan Automobile Manufacturers Association (JAMA) 50th percentile male.

This paper addresses the need for fundamental understanding of the mechanisms of fuel spray formation and mixture preparation in direct injection spark ignition (DISI) engines. Fuel injection systems for DISI engines undergo rapid developments in their design and performance, therefore, their spray breakup mechanisms in the physical conditions encountered in DISI engines over a range of operating conditions and injection strategies require continuous attention. In this context, there are sparse data in the literature on spray formation differences between conventionally drilled injectors by spark erosion and latest Laser-drilled injector nozzles. A comparison was first carried out between the holes of spark-eroded and Laser-drilled injectors of same nominal type by analysing their in-nozzle geometry and surface roughness under an electron microscope.

Unlike RANS method, LES method needs more time and much more grids to accurately simulate the spray process. In KIVA, spray process was modeled by Lagrangain-drop and Eulerian-fluid method. The coarse grid can cause errors in predicting the droplet-gas relative velocity, so for reducing grid dependency due to the relative velocity effects, an improved spray model based on a gas-jet theory is used in this work and in order to validate the model seven different size grids were used. In this work, the local dense grid was used to reduce the computation cost and obtain accurate results that also were compared with entire dense grid. Another method to improve computation efficiency is the MUSCL (Monotone Upstream-centered Schemes for Conservation Laws) differencing scheme that was implemented into KIVA3V-LES code to calculate the momentum convective term and reduce numerical errors.

This paper describes the development of high efficiency and compact bumper recycling equipment for facilitating bumper recycling globally. Various equipment to remove paint coat from bumper has been developed since 90s', using mechanical, physical or chemical method. However, it is difficult to promote bumper recycling without realizing cost effective overall system from paint coat removal to pelletizing. Our company jointly developed method of mechanically removing paint coat and has committed to bumper recycling in the form of outsourcing since 2000. In 2010, a dedicated plant for recycling bumpers was launched on the premises of our Oppama Assembly Plant in Japan. In the future, promoting bumper recycling at other overseas assembly plants is necessary as vehicle production will expand globally.

A comprehensive analysis was performed to evaluate the effect of BMI on different body region injuries for side impact. The accident data for this study was taken from the National Automotive Sampling System-Crashworthiness Data System (NASS-CDS). It was found that the mean BMI values for driver and front passengers increases over the years in the US. To study the effect of BMI, the range was divided into three groups: Thin (BMI<21), Normal (BMI 24-27) and Obese (BMI>30). Other important variables considered for this study were model year (MY1995-99 for old vehicles & MY2000-08 for newer vehicles), impact location (side-front F, side-center P & side-distributed Y) and direction of force (8-10 o'clock for nearside & 2-4 o'clock for far-side). Accident cases involving older occupants above 60 years was omitted in order to minimize the bone strength depreciation effect. Results of the present study indicated that the Model Year has influence on lower extremity injuries.

A logistic regression analysis of accident cases in the NASS-PCDS (National Automotive Sampling System-Pedestrian Crash Data Study) database clearly shows that pedestrian pelvis injuries tend to be complex and depend on various factors such as the impact speed, the ratio of the pedestrian height to that of the bonnet leading edge (BLE) of the striking vehicle, and the gender and age of the pedestrian. Adult female models (50th %ile female AF50: 161 cm and 61 kg; 5th %ile female AF05: 154 cm and 50 kg) were developed by morphing the JAMA 50th %ile male AM50 and substituting the pelvis of the GHBMC AM50 model. The fine-meshed pelvis model thus obtained is capable of predicting pelvis fractures. Simulations conducted with these models indicate that the characteristics of pelvis injury patterns in male and female pedestrians are influenced by the hip/BLE height ratio and to some extent by the pelvis bone shape.

Aircraft icing is a significant issue for aviation safety. In this paper, recent developments for calculating the trajectory of non-spherical particles are used to determine the trajectory and impingement of ice crystals in aircraft icing scenarios. Two models are used, each formulated from direct numerical simulations, to give the drag, lift and torque correlations for various shaped particles. Previously, within the range of Reynolds number permitted in this study, it was only possible to model the trajectory and full rotational progression of cylindrical particles. The work presented in this paper allows for analysis of a wider range of ice shapes that are commonly seen in icing conditions, capturing the dynamics and behaviours specific to ice crystals. Previous limitations relate to the in ability to account for particle rotation and the dependency of force correlations on the measure of particle sphericity - which are now overcome.

A significant amount of harmful emissions pass unreacted through catalytic after-treatment devices for IC engines before the light-off temperature is reached, despite the high conversion efficiency of these systems in fully warm conditions. Further tightening of fleet targets and worldwide emission regulations will make a faster catalyst light-off to meet legislated standards hence reduce the impact of road transport on air quality even more critical. This work investigates the effect of adding hydrogen (H2) at levels up to 2500 ppm into the exhaust gases produced by combustion of various oxygenated C2-, C4- and renewable fuel molecules blended at 20 % wt/wt with gasoline on the light-off performance of a commercially available three-way catalyst (TWC) (0.61 L, Pd/Rh/Pt - 19/5/1, 15g). The study was conducted on a modified naturally aspirated, 1.4 L, four-cylinder, direct-injected, spark-ignition engine.

This paper presents a study of a cooled exhaust gas recirculation (EGR) system applied to a turbocharged gasoline engine for improving fuel economy. The use of a higher compression ratio and further engine downsizing have been examined in recent years as ways of improving the fuel efficiency of turbocharged gasoline engines. It is particularly important to improve fuel economy under high load conditions, especially in the turbocharged region. The key points for improving fuel economy in this region are to suppress knocking, reduce the exhaust temperature and increase the specific heat ratio. There are several varieties of cooled EGR systems such as low-pressure loop EGR (LP-EGR), high-pressure loop EGR (HP-EGR) and other systems. The LP-EGR system was chosen for the following reasons. It is possible to supply sufficient EGR under a comparatively highly turbocharged condition at low engine speed.

Particulate emissions are of growing concern due to health impacts. Many urban areas around the world currently have particulate matter levels exceeding the World Health Organisation safe limits. Gasoline engines, especially when equipped with direct injection systems, contribute to this pollution. In recognition of this fact European limits on particulate mass and number are being introduced. A number of ways to meet these new stringent limits have been under investigation. The focus of this paper is on particulate emissions reduction through improvements in fuel delivery. This investigation is part of the author's ongoing particulate research and development that includes optical engine spray and combustion visualisation, CFD method development, engine and vehicle testing with the aim to move particulate emission development upstream in the development process.

Low speed pre-ignition (LSPI) is a limiting phenomenon for several of the technologies being pursued as part of the low carbon agenda. To achieve maximum power density and efficiency engines are being downsized and turbocharged, while Direct- injection technologies are becoming ever more prominent. All changes that increase the propensity of LSPI. The low speed-high load operation envelope is limited due to LSPI. Hydrogen engines are also being explored, however, with such a low minimum enthalpy of ignition, LSPI is a major limitation to thermal efficiency. Several techniques are utilized in this study to investigate physical and physio-chemical aspects of lubricant initiated LSPI. Where possible attempts have been to validate methodologies or directional alignment with published data. The basis of the methodologies used is a validated 1D predictive combustion model of a single cylinder GTDI engine, that was used to provide simulation boundary conditions.